Drums · Guides
Mixing Big Drums: Editing, Phase and Processing
Mixing big drums is mostly about keeping a dozen or more microphones working together: edit them as one, notch the resonances that clog the midrange, compress the room rather than the kit, and ride the room mics up when the song gets bigger. This is our workflow in Cubase at Hot Milk Studio.
Robert Cummings — producer, engineer and drummer
· 5 min read

Routing: build the kit from prebusses
Bass drum in and out feed a BD prebus, snare top and bottom an SD prebus, the toms a tom prebus, and the overheads and room mics their own prebusses. Everything ends up on one drum bus. This makes it easy to balance the kit in a few moves and to process pairs of mics together.
Editing without breaking phase
- Edit all mics together. All drum tracks sit in one folder with group editing on. Moving the snare mic alone by even a fraction of a millisecond changes how it sums with the overheads.
- Cut just before a loud hit — and before the transient on the earliest mic, the close mic. A short crossfade there is practically inaudible.
- Comp between takes with the cymbal decays intact and a consistent snare tone.
- Clean up afterwards: tom tracks are muted between hits (or turned down), hi-hat and ride tracks tidied, uneven hits evened out with clip gain.
- We don't use automatic multitrack time-stretching on drums; in our experience it adds artefacts.
Balance before processing
After editing, we take a break and listen to the whole song first. Usual suspects: snare bottom too loud, bass drum out too loud, overheads and rooms too loud, a muddy midrange, ringing close mics. Most problems get smaller with faders and panning alone.
EQ: notch the ring, avoid the high-pass
- Find the fundamental of each drum and leave it or boost it gently.
- Notch the ringing overtones. Drumhead overtones are not at octaves: for an ideal membrane they sit at roughly 1.59, 2.14, 2.30 and 2.65 times the fundamental. So we find them by sweeping and listening, not by calculating. Removing them usually makes the drums louder and clearer. Many crash cymbals also have a harsh resonance around 5–6 kHz.
- Avoid high-passing every mic. Each high-pass filter shifts the phase of the frequencies near its cutoff, so different filters on different mics change how they sum and the low end loses focus. Gentle low shelves do less damage; if real high-passing is needed, we do it once on the drum bus, where all mics are filtered identically.
- Broad boosts sound best on analog-style EQ — for example our Neve-style Warm Audio EQs or the Pultec-style Tegeler EQP-1.
Compression and saturation
- Top-down first: the Tegeler Magnetismus 2 on the drum bus shapes the peaks of the performance.
- Gentle prebus compression: around 2–3 dB of gain reduction on bass drum, snare and toms, slow attack, medium release.
- Parallel compression keeps the dynamics of the performance while adding density: a gated, heavily compressed copy of the snare, blended in until it's too much, then backed off 1–2 dB.
- Compress the room: heavy compression on the room mics is often our favourite "parallel" compression — watch for crashes pumping.
- Side-chain tricks: the snare briefly ducks the overheads for extra punch; a gated snare can key a gate on the room mics for a classic 80s gated sound, which works beautifully with the ambience of our main room.
- Saturation: peaky snares and hi-hats love tube saturation such as the SPL Charisma; a transient designer brings back attack if saturation softens it.
- Hard clipper last on the drum bus to catch stray snare peaks before the master limiter.
Hardware like the Magnetismus 2 and Charisma is also available for your own tracks: analog processing.
Automation: let the drums grow with the song
A big drum sound shouldn't be static. We ride the room mics up in choruses and big drum fills and pull them back in verses, so the song gains size exactly where it needs it.
Reverb and samples — sparingly
- Drums from our main room rarely need much artificial reverb; when we add it, we use mainly the tail (the recording already has early reflections) and EQ the low end and harsh upper mids out of the return.
- We have impulse responses of our own rooms and of the long-tail stairwell in our building.
- Samples are tools, not crutches. We prefer samples recorded in the same session — same kit, same tuning, few phase issues — aligned to the snare transient and checked for polarity. Too much and the performance sounds robotic.